VW2L Wideband LNB – 2 Output
Main features:
- Finished in grey
- Supplied with a SkyTM compatible bracket
- Built-in spirit level
Wideband Technical Specification
Input Frequency: 10.7 ~ 12.75 GHz
Output Frequency : Vertical: 290 ~ 2340 MHz / Horizontal: 290 ~ 2340 MHz
L.O. Frequencies: 10.41 GHz
L.O. Stability: +/-0.5 MHz (max) @ Room Temp. +/-1 MHz (max) @ -40°C ~ +60°C
L.O. Phase Noise: -50dBc/Hz @ 1kHz (max.) -75dBc/Hz @ 10kHz (max.) -100dBc/Hz @ 100kHz (max.)
Noise Figure: 0.1 dB (typ.)
Conversion Gain: 50 dB (min) / 60 dB (max)
Gain Flatness @ 26MHz: +/-0.5dB (typ.)
Gain Variation: 7dB (max.) @ full band
Cross Polar Isolation: 25 dB (typ.)
Image Rejection: 40 dB (min)
Current Consumption 0.85W (max.) (70mA @ +12V DC)
Power Voltage: 9 - 19V DC
Connector Type: 75Ω female F-connector
Output Spurious: <-60dBm
Operating Temp.: -40’C ~ +60’C
RED Compliance: EN 303 372-1
Legacy Technical Specification
Input Frequency: low band: 10.7 ~ 11.7 GHz high band: 11.7 ~ 12.75 GHz
Feedhorn - Linear: Optimised for offset dish
Output Frequency Output 1, 2, 3, 4: low band: 950 ~ 1950 MHz / high band: 1100 ~ 2150 MHz
Output 1,2,3,4 VSWR (950 - 2150 MHz): Ratio 2.0:1 (typ.), 2.5:1 (max.)
L.O. Frequencies: 9.75 / 10.6 GHz
L.O. Stability: 0.5 ~ 1.0 MHz
L.O. Phase Noise: -55dBc/Hz @ 1kHz (max.) -75dBc/Hz @ 10kHz (max.) -90dBc/Hz @ 100kHz (max.)
Conversion Gain: 56 ~ 63 dB @ 25ºC / 54 ~ 60 dB @ -40ºC ~ 60ºC
Gain Flatness Over Full Band: 3 dB P-P (typ.), 5 dB P-P (typ.)
Gain Flatness @ 26MHz: +/- 0.5 dB P-P (typ.)
Gain Flatness @ 300MHz: +/- 4 dB P-P (typ.)
1.7GHz: -50 dB (typ.) -47 dB (max.)
Noise Figure: 0.3 dB (typ.), 1.0 dB (max.)
Cross Polar Isolation: 18 dB (min.), 20 dB (typ.)
Image Rejection: 37 dB (min), 40 dB (typ.)
Current Consumption: 120mA (typ.), 140mA (max.)
Operating Voltage & Band Switching: Vertical 11.5 - 14.5 VDC / Horizontal 15.5 - 19 VDC / Low-Band 0 KHz / High-Band 18 - 26 KHz
Connector Type: 75Ω female F-connector
Operating Temp.: -40ºC ~ +60ºC
RED Compliance: EN 303 372-1
Please note: for use with Sky Q STBs you must use both the 2 designated wideband outputs.
